ViewSonic PJD6211P Wartungshandbuch

Service Manual ViewSonic PJD6211Model No. VS12618DLP Projector(PJD6211_SM Rev. 1b Nov.2009)ViewSonic® 381 Brea Canyon Road, Walnut, California 91789 U

1.3 PJD6211 Lamp SpecificationProduct ScopeThe product is a lamp system consisting of a short arc burner within a reflector and electronic lampdriver.

Safety Protections The lamp connections are not mains isolated, The lampcan be switched on via the Start Control Input signal(SCI).A Fla

 The lamp contains mercury. If the lamp bursts during operation ventilate the areasufficiently to avoid inhaling harmful mercury fumes. Use the lead

1.4 PJD6211 System Block DiagramViewSonic Corporation Confidential - Do Not Copy PJD621110

2. Firmware Upgraded FlowThis chapter provides the information regarding relevant equipments and upgradingprocedure for firmware upgrade.Note:1. Plea

2.1 Setup Tool/Equipment Computer USB Cable (See the picture) Power Cord2.2 Upgrading ProcedureInstalling [DLP Composer (TM) Lite]1. Double-click [

USB Support - Installation (All Platforms)This release includes support for a USB communications interface to DDP2 230/DDP2430based projectors. The se

6. Move the cursor to [Flash Loader] on the Project window of [DLP Composer Lite]. (The[Flash Loader] screen will appear.)7. Click [Browse] and select

12. Wait for the Completion of Burning and then remove Power Cord and USB Burning Cord.ViewSonic Corporation Confidential - Do Not Copy PJD621115

3. Machine Disassembly and Replacement3.1 ToolsItem PhotoLong Nose NipperHex Sleeves 5mmScrew Bit(+):107Screw Bit(+):101Screw Bit(+):102Anti-static wr

CopyrightCopyright© 2009 by ViewSonic Corporation. All rights reserved. No part of this publication may bereproduced, transmitted, transcribed, stor

3.2 Disassembly ProcedureWarning Put on the Static Electricity Ring when starting for repair. Repair Environment suggest in Clean -room class 10000.

Step Figure Description1Press the power button toshutdown the projector anddisconnect the power cord.If the lamp is hot, please donot start any proced

Step FigureDescription41. Disconnect the FFC cableand safety switch betweentop cover and main board.2. Raise the Top Cover.51. Loosen the one screw to

Step FigureDescription71. Remove the five screwson the Main Board.2. Remove the metal sheet ofMain Board.Note: The Back IR wire isconnected to Main Bo

Step FigureDescription101. Loosen the two screws asshown and remove all wireson RS232 Board.2. Remove the RS232Board.11Loosen the two screws asshown t

Step FigureDescription12Release the four pillars byLong Nose Nipper to removethe Ballast.131. Remove the screws on theoptical engine.2. Remove the opt

Step FigureDescription151. Loosen the two screwson the OE Fan.2. Remove the Fan.3. Loosen the four screwson DMD Board.4. Remove the heat sinkand DMD B

Step FigureDescription181. Remove Speaker Module.2. Loosen the screws andremove front and back IR.3.3 Assembly FAN ModuleStep Figure Description1Assem

3.4 Disassembly Lamp ModuleAs the projector operates over time, the brightness of the projector lamp gradually decreasesand the lamp becomes more susc

4. Troubleshooting and Verifying the RepairThis chapter provides technicians with electronic background how to maintain the product.Moreover, you can

1 System Introduction ... ... ... 11.1 Technical

(2) Confirm LED indicatorLED Type Color Status MeaningPower LED Blue Solid(LED× 1)Lamp LED Off OffTemp LED Off OffThe projector is in standby mode.Pow

Note: Swapping modules that may be defective with others known to be good is generally an ideal way tofind the module responsible for the problem. A f

Power Source Troubleshooting:No PowerSource afterturning onReplace ACsocketReplace powerboard or reinstallReplace keypadand FFCReplacepower boardRepla

Fail to light upRefer to LEDindicator and followindicative actionsReplaceLamp ModuleReplacePower boardReplaceBallastReplaceMain boardOKOKOKOKOKNGNGNGN

Signal TroubleshootingComputerNo SignalTurn onSourceReplaceCableReplaceMain boardOKOKNGNGNGCheckOutput signalCheckCableCheckSourceVideoNo SignalTurn o

Image abnormalAdjustInput signalReplaceMain boardReplaceOptical EngineOKOKOKNGNGNGCheckOptical EngineCheck inputcable and signalsettingPower onagain a

Operation Function TroubleshootingRemote ControlFailureReplaceBatteryReplaceRemote ControlReplaceIRReplaceMain boardOKOKOKNGNGNGNGCheckMain boardCheck

4.2 Verifying the RepairAfter repairing projector (Dissembling and assembling projector), Repair center should verifythe quality of repaired unit.(1)

Test EquipmentPC and Remote controllerTest method1. Connect PC (laptop) VGA output to projector.Set PC (laptop) output signal to projector2. Connect p

Zoom ring and Focus ringRing Test criteriaZoom ringMechanical motion of rotating Zoom ring to the end of right and left byhand should be free from get

1. System Introduction1.1 Technical SpecificationViewSonic Corporation Confidential - Do Not Copy PJD62111

Extreme Gray-Scale--0 represents full black, 255 represents fullwhite.--Distinguishing the gray from black at thevalue of 32 and the gray from white a

INFOCOMM SMPTE 1331. The intervals of center thin white andblack bars should be distinct.2. The squares around the small circle inthe center show the

(6) Front and Rear infrared sensorDeviceFront and Rear infraredTest EquipmentRemote controllerTest method1. Cover front sensor and operate remote cont

5. Connector InformationThis section provides each connector location on boards and function of each board. They willbe useful for your detecting the

Connector DescriptionNo 3 SpeakerNo 4 Color Wheel controlNo 5 Color Wheel SensorNo 6 Ignite signal connected to BallastNo 7 Lamp FANNo 8 Thermal senso

5.4 Power BoardConnector DescriptionNo 1 380V output for ballastNo 2 12V output for RS232 boardNo 3 12V/5V output for Main boardNo1No2No3ViewSonic Cor

6. FRU (Field Replaceable Unit) ListIntroductionThis section is a list of all the FRU removal . Following the FRU table of contents is an enlargedview

6.1 Mechanical Drawing16. FAN217. FAN 113. Back IR19. Bottom Cover18. Power Board14. Ballastmetal sheet of IO Port12. Front IR15. Speakermetal sheet o

Item ViewSonic P/N Ref. P/N Description Q'ty1 C-00009631 P4S84-4500 Top Cover 12 C-00009638 P4E34-4650-00 Lens Cover 13 C-00009633 P4S84-4530 IO

淋膜袋主線物料請按照以上折疊順序以此折好請用透明膠帶按照上圖貼好Warning lb2. P2838-5001-00加貼底蓋位置(如圖)MAC ADDRESS LB如圖示位置加貼如圖示位置加貼5mm5mm5mm3mmEPE7. P4R39-7001-00鏡頭在此處UL LB 5. P4S38-500

1.2 Location of features, Controls, and I/OA. Projector overviewFront View1. Lens cap 7. Filter cover2. Elevator button 8. Speaker3. Lens cap strap 9.

SHEET11. P4R39-4800-00所有線材和電池一起放入15. J4039-R184-01後放於此處遙控器放在最上面HDPE BAG14. 04039-R157-01QG12. P4R39-4000-00CD13. P4R39-A000-00入膠袋后放入卡板中間槽位中REMOTE CONT

Item ViewSonic P/N Ref. P/N Description Q'ty1 NA P1638-5007-00 LB 12 NA P2838-5001-00 WARNING LB 13 NA P1638-5010-00 LB 14 NA J4238-R815-01 SERIA

7. MaintenanceThe projector needs proper maintenance. You should keep the lens clean as dust, dirtor spots will project on the screen and diminish ima

8. Recommended Spare Parts ListViewSonic Corporation Confidential - Do Not CopyViewSonic Model Number: VS12618Serial No. Prefix: RCTRev: 1bItem Catego

Appendix A: RS-232 Command and Confi gurationBaud Rate: 19200 Parity Bit: noneData Bit: 8 Stop Bit: 1 Assign Port: COM1Name Operation type CRS He

System Status BE,EF,03,06,00 04,D8 71,00,00,00,00,0003:ProjectorON(NormalMode)ViewSonic Corporation Confidential - Do Not Copy PJD621152

Appendix B: IR Control CodeViewSonic Corporation Confidential - Do Not Copy PJD621153

Appendix C: How to reset the Lamp Hours(OK)(1) Press “Menu” button to open the Main menu.(2) Move color bar to “setting” item and then press right but

(4) Press the direction keypad following the actions below to enter engineering mode:Right once, left twice, right three t imes, left four times.(5)

(6)Press left button to select “yes” to reset Lamp Hours .(7)Then the Lamp Hours would reset to 0 hours.ViewSonicCorporation Confidential - Do Not Cop

Real View1. Connection ports 2. AC power socket3. Kensington lock 4. Rear IR remote control sensor5. Ventilation holes (exhaust) 6. Security barBottom

* Reader’s Response*Dear Readers:Thank you in advance for your feedback on our Service Manual, which allows continuous improvementof our products. We

B. Button function and LED indicatorLED1.Power (Power LED indicator)2. Temp (Temperature LED indicator)3. Lamp (Lamp LED indicator)Button function4.Ke

C. Connection ports1. USBThis connector is for firmware update and mouse function support.2. VideoConnect composite video output from video equipment

D. Remote ControlViewSonic Corporation Confidential - Do Not Copy PJD62116